1. Advertising
    y u no do it?

    Advertising (learn more)

    Advertise virtually anything here, with CPM banner ads, CPM email ads and CPC contextual links. You can target relevant areas of the site and show ads based on geographical location of the user if you wish.

    Starts at just $1 per CPM or $0.10 per CPC.

ASK (How to enable RDP via web)

Discussion in 'Web Hosting' started by ceo.worldfriend.web.id, Apr 29, 2013.

  1. #1
    How to enable RDP via web in Windows Server
    ceo.worldfriend.web.id, Apr 29, 2013 IP
  2. MilesGeek

    MilesGeek Active Member Premium Member

    Messages:
    637
    Likes Received:
    12
    Best Answers:
    5
    Trophy Points:
    88
    #2
    RDP is a service which works on a specific port & cannot be accessed via web browser unless and until you embed it using java and access it using web browser. You will need to use a third party utility to have it embedded with java to be accessible using a browser.
    MilesGeek, Apr 30, 2013 IP
  3. PolkRB

    PolkRB Active Member

    Messages:
    50
    Likes Received:
    0
    Best Answers:
    0
    Trophy Points:
    51
    #3
    There is a scenario where RDP might be disabled on server, but you have NETBIOS network access, there are tools available that can enable RDP remotely. But it will not be via web in anyway.
    PolkRB, May 3, 2013 IP
  4. nastyguys

    nastyguys Member

    Messages:
    114
    Likes Received:
    0
    Best Answers:
    0
    Trophy Points:
    26
    #4
    please find below information

    You can use Remote Desktop Web Connection to connect to a remote computer over the Internet. To do this, the remote computer must be running Windows Server 2008, and Terminal Services Web Access (TS Web Access) must be installed. (For information about installing TS Web Access, go to Terminal Services Web Access (TS Web Access) on the Microsoft TechNet website.) Here's how to connect to a remote computer using a web connection:
    1. Open Internet Explorer or another web browser, and type the URL using the remote computer's name or IP address, followed by /tsweb/
    2. On the Remote Desktop Web Connection logon screen, in Connect to or Server, type the server name (the remote computer name), and then click Connect.
    3. Type your user name and password, and then click OK.
    When you are ready to disconnect, log off and then close your browser.
    nastyguys, Jun 5, 2013 IP
  5. hosting_spec80

    hosting_spec80 Active Member

    Messages:
    130
    Likes Received:
    5
    Best Answers:
    0
    Trophy Points:
    53
    #5
    If you have RDP access to your server and want to enable multiple RDP connections, do the following:
    1. Log into the server using Remote Desktop.
      • In Windows 2008 R2
        • Click Start > Administrative Tools > Remote Desktop Services > Remote Desktop Session Host Configuration.
      • In Windows 2008
        • Click Start > Administrative Tools > Terminal Services >Terminal Services Configuration.
    2. Double click Restrict Each User to a Single Session.
    3. Uncheck Restrict each user to a single session.
    4. Click OK.
    hosting_spec80, Jun 5, 2013 IP
  6. ceo.worldfriend.web.id

    ceo.worldfriend.web.id Member

    Messages:
    22
    Likes Received:
    0
    Best Answers:
    0
    Trophy Points:
    31
    #6
    Whether conditions should IIIS Start? then is there any way to windows server 2013 or 2003
    ceo.worldfriend.web.id, Jun 6, 2013 IP